******************************************************************************
Release Notes for Vigor2710 series

Firmware Version	: 3.6.3 (Release)
Release Date		: 2nd January 2012
Build Date		: 16th October 2012
Applicable Models	: Vigor2710, Vigor2710n, Vigor2710Vn, Vigor2710VDn
Locale			: UK Only / Annex A Only

******************************************************************************

[New Features]
1.  IPv6 Support Added
2.  Smart Bandwidth Limit support added
3.  QoS DiffServ retagging support added
4.  ADSL PVC to PVC binding added
5.  VoIP Wizard added

[Improvement]
1.  Removed ADSL2/2+ Annex M from "multimode" auto-detect mechanism due
to interoperability issues that could cause incorrect modulation to be set. For
Annex M lines please manually set the modulation to Annex M instead of multimode.
2.  DNS function does a force update even no WAN IP changed.
3.  Removed incorrect PPP start (xxx) log entry where incoming client is unknown prior to CHAP/PAP authentication
4.  Can not show the FTP file list when Android phone connecting to Vigor2710 FTP server.
5.  True IP DMZ may not work.
6.  Incorrect wireless country string which will be checked by Linux and MAC.
7.  May meet reboot problem while running wireless AP Discovery.
8.  A user can send a FAX not only using T.38 protocol but also G.711.
9.  Resolves an issue which would prevent IP Phones behind the Vigor 2830 from registering after a WAN failover
because the router would sent UDP packets with a source port of 0.
10. DHCP Relay via VPN tunnel can not work.
11. QoS classify error for transmission traffic to VPN L2TP tunnel.
12. Cannot apply AES 192 and AES 256 on IPSec Security Method while the
customer chooses options of AES without authentication in VPN and Remote
Access>>LAN to LAN page.
13. Firewall can't block internal routing subnet packets.
14. UCF Syslog cannot show HTTP or HTTPS.
15. A CPE may loss connection when it connects to VigorACS server with STUN
server.
16. A router without VoIP module should not have an option "VoIP" in
Multi-PVCs setting page.
17. WCF service stability improvements
18. Online Status shows error secondary DNS value.
19. Add a Clear button in the web page for SIP account.
20. Lease time on DHCP server is configurable.
21. By looking at the syslog, we can see who has acquired the IP dispatched from our router.
22. The router can send the TR-069 packet out via LAN interface.
23. Moify the default pool size of LAN DHCP server from 50 to 150.
24. Add new DDNS provider (UBDdns, Oray, and Peanut Shell).
25. Improve Samba with Mac OS X.
26. Bandwidth Limit range change to 0 - 30000.
27. Block Skype version 5.10.56.116.
28. ADSL state information update frequency to syslog decreased from 5 to 30 seconds
29. Rename "Undefined Protocol" with "Unassigned Numbers" for the DoS
function.
30. Disable QoS by default for non-VoIP models.
31. Enhance VoIP QoS.
32. Improve ALG for SoftPhone Polycom and lift-size.
33. Improve the web page for VPN Profile.
34. Modify UCF(URL Content Filter)/WCF(Web Content Filter) block web page.
35. SNMP's sysDescr can show model name and firmware version.
36. TR-069 support added for IP Route subnet parameters, firewall parameters,
RADIUS  parameters, WAN Connection Detection and SysLog / Mail Alert Setup parameters
37. Renamed TR-069 parameter "InternetGatewayDevice.X_00507F_Firewall.DoSDefense.BlockUnknownProto" to "InternetGatewayDevice.X_00507F_Firewall.DoSDefense.BlockUnassignedNum"
38. ip arp accept telnet command changed to give separate control over behaviour (pass or block) for both incorrect source mac and incorrect destination mac. 'ip arp accept <0/1/2/3/status>' 
39. Added a telnet command to configure IGMP Query packet interval time. 'ip igmp_proxy query [msec]'
40. Added a telnet command to configure flash hook minimum and maximum time for VoIP.

******************************************************************************
Release Notes for Vigor2710 series

Firmware Version	: 3.3.7 (Release)
Release Date		: 20th June 2012
Build Date		: 23rd February 2012
Applicable Models	: Vigor2710, Vigor2710n, Vigor2710Vn, Vigor2710VDn
Locale			: UK Only / Annex A Only

******************************************************************************

[New Features]
1.  Supports sending Syslog via email.
2.  Supports auto-detection of other locally connected DrayTek devices.
3.  Supports detecting ADSL2/2+ Annex J and Annex M with Multimode DSL modulation.
4.  Added Address Mapping under the NAT menu.
5.  Supports hardware MD5/SHA1 encryption.
6.  Supports Syslog Explorer with Web Syslog and USB Syslog under the USB Application menu.
7.  Allow Mail Alert to send emails with VPN notifications.

[Improvement]

[VoIP]
1.  Improved: Added a telnet command to disable/enable internal VoIP service "voip sip misc -D" on 2710Vn/VDn.
2.  Improved: Added telnet command for adjusting the volume of call waiting tone.
3.  Improved: SIP address format (either Withheld@X or anonymous@X ) can be blocked if Block Anonymous under VoIP>>DialPlan>>Call Barring is configured.
4.  Improved: Incoming calls with SIP from header field without having an account name (e.g., tagged with 5E623524-172D) 
    can be blocked if Block Anonymous under VoIP>>DialPlan>>Call Barring is configured.
5.  Corrected: VoIP call may drop after 2-3 minutes.

[WAN]
6.  Improved: Add MTU setting on PPPoE/PPPoA and MPoA page.
7.  Corrected: WAN cannot get IP from DHCP server when Block Fraggle Attack is checked in the page of Firewall > DoS Defense.
8.  Corrected: Ping detection fails when the target IP and gateway are in the same subnet.

[General]
9.  Improved: Added a telnet command to set user-defined custom DHCP options "srv dhcp custom_option"
10. Improved: Supports disabling/enabling user mode in the web interface. The factory default setting is disabled.
11. Improved: Improved compatibility with VigorACS SI v1.08.
12. Improved: Corrected some LAN status SNMP information.
13. Improved: Shows correct German umlauts in Samba server.
14. Improved: A Reboot could occur while printing with the USB port for some printers.
15. Corrected: QoS may not work correctly if the firewall is disabled.
16. Corrected: Data Flow Monitor did not show TX & RX value for the monitored IP address when using WAN on PPTP Host-LAN environment.
17. Corrected: RIP over VPN may not work.
18. Corrected: My WAN IP setting does not work when using PPTP in NATted VPN mode.
19. Corrected: Buffer leakage occurs when IPSec Aggressive mode is used and configured with a local IP address.
20. Corrected: User-Based mode of user management does not work if HTTPS management port has been changed.
21. Corrected: Firewall caused a problem with SIP registrations.


******************************************************************************
Release Notes for Vigor2710 series

Firmware Version	: 3.3.6.1 (Release)
Release Date		: 14th April 2011
Build Date		: 22nd March 2011
Applicable Models	: Vigor2710, Vigor2710n, Vigor2710Vn, Vigor2710VDn
Locale			: UK Only / Annex A Only

******************************************************************************

[New Features]
1. Add the static route for IPSec LAN to LAN with NAT mode.
2. Added configurable QoS

[Improvement]
1.  Corrected: A crash occurred while pressing the space bar after typing "qos class -V 1"
telnet command.
2.  Domain name now supported in STUN server IP field in TR-069 web page.
3.  USB storage file handling improvements
4.  Added default Busy tone and Congestion tone parameters for UK.
5.  Fixed issue with displaying [Firewall]>[General Setup] page of view Filter Rule in WebUI
6.  Corrected SNMP response for 1.3.6.1.2.1.4.20.1.1 in WAN PPP mode.
7.  Access list was previously blocking access to router web interface via VPN
8.  L2TP over IPSec memory handling improvements with PPTP/PPPoE WAN connections
9.  Improvments in handling of WLAN probe response to WLAN client
10. Wireless connection improvments
11. Syslog output for Wireless security settings amended
12. Added Syslog output of VoIP debug messages
13. Corrected RTP CODEC selection for callee when multiple ports are ringing for one account
14. Improvements to Call Transfer mechanism
15. It was not possible to re-enable PSTN ring FXS port after it was disabled by telnet command of
pstnringfxs.
16. The incorrect codec was displayed on VoIP status page if codec was set to any of iLBC_13, iLBC_15, or G.722_64.
17. Can not see "PT=Comfort noise" in RTP packet of WAN when Codec is G.711 and Voice Active Detector of DECT is enabled.
18. Issue with Outband DTMF via DECT phones fixed
19. Support TR-069 parameter for VigorACS SI.
20. Support WINS DHCP Option for DHCP server.
21. Warning message will appear if MTU size is set lower than 1000.
22. Protection added to prevent setting the same value in Call Filter and Data Filter.
23. At least One SSID must be selected on the Wireless LAN>>Access Control page.
24. Added Caller ID display from PSTN (NL)
25. By default disabled ringing dis-bounce to correct PSTN caller ID display error in
Netherlands. You can use the telnet command to control ringing dis-bounce.
voip dsp relaydbounce [on|off]
26. Added a new telnet command for "Change default route to this VPN". vpn option <index> droute=on/off.
27. Add a new telnet command to control "Display Name" as "PADI service name" for WAN.
internet -P <on/off>
(on "Display Name" can be treated as "PADI service name")


******************************************************************************
Release Notes for Vigor2710 series

Firmware Version	: 3.3.2 (Release)
Release Date		: 29th Jan 2010
Build Date		: 4th Dec 2009
Applicable Models	: Vigor2710, Vigor2710n, Vigor2710Vn
Locale			: UK Only / Annex A Only

******************************************************************************

Please ensure you download and use the latest router tools when upgrading the firmware.

[New Functions]
1. Support USB Disk Application (FTP/Samba).
2. “twodns” DDNS service.
3. Support PPPoA pass-through function.
4. Show source MAC address on Syslog for LAN to WAN packets.

[Improvements & Corrected Problems]

5. Corrected: Dial Out Account can not be set to default on DialPlan Setup of WUI.
6. Corrected: If the phone is disabled but the phone state is not changed, the phone will not ring when receiving PSTN incoming call.
7. Corrected: Resolved issue that When RFC-2833 with payload type = 96 packet is received, the router will reboot.
8. Corrected: SIP memory leakage.
9. Corrected: Problem for semi-attendent CT for VoIP.
10. Corrected: Can not save DSL settings sometimes after finishing Auto Detection in Quick Start Wizard.
11. Corrected: Some problems occurred on WUI.
12. Corrected: Can not get TR069 parameters after meeting TR069 connection timeout.
13. Corrected: Firmware upgrade may be failed when upgraded by TR069.
14. Corrected: UCF can save 12 objects, only.
15. Corrected: Call filter malfunctioning.
16. Corrected: Failure of running IP Ping through PPTP of VPN.
17. Corrected: Adding UPNP port mapping failed.
18. Corrected: Connection problem on PPTP NAT pass-through.
19. Improved: Wildcard '?' can be used in Digit Map.
20. Improved: Allowed VoIP number starting with # for non-IP calls.
21. Improved: Wireless interoperability with Vigor AP700 while using WDS with WPA or WPA2 mode.
22. Improved: Mouse cursor stays on the field of Username in Login page of Web UI.
23. Improved: Add/modify some TR069 parameters.
24. Improved: Router stability against NMAP scan.
25. Improved: Bridge mode may not work after powering off/on.
26. Improved: Add/modify some IM/P2P signatures.
27. Improved: ARP cache life settings stored to flash so that value is saved even after reboot of the router.
28. Improved: Increase compatibility with more stun servers.


******************************************************************************
Release Notes for Vigor2710 series

Firmware Version	: 3.3.0 (Release)
Release Date		: 5th August 2009
Build Date		: 5th August 2009
Applicable Models	: Vigor2710, Vigor2710n, Vigor2710Vn
Locale			: UK Only / Annex A Only

******************************************************************************

[New Functions]	

1. Upgrade VoIP driver for add improvements.
2. Add/modify signatures to block new version PPStream.
3. Add/modify signatures to block new version UUSee.
4. Add telnet command to enable/disable blocking of illegal ARP REPLY packet (Ethernet source address
doesn't match ARP sender address)
5. Add SIP Account setting item in user mode.
6. Add "Select All" button in IM object page, P2P Object page, Protocol Object page, Misc
Object page.
7. Add "Loop Through To PSTN" in VoIP Status on WUI

[Improvements & Corrected Problems]

1. Corrected: Got error message while running firmware upgrade on Firefox 3.0.3.
2. Corrected: Meet connection problem while running P2P service & enabling session limit.
3. Change Wireless MAC Address to upper case on WUI.
4. Corrected: DDNS send request error.
5. Corrected: DDNS Auto-Update interval value can't be cleared or set to factory default
value.
6. Corrected: A problem of DHCP MaxAddress Provision for TR069.
7. Corrected: A problem of ProvisionKeepParameter crash for TR069.
8. Corrected: Set WPS client's default MAC address as 00-00-00-00-00-00 to avoid WUI
display error.
9. Corrected: CPA query timeout problem will be occurred while DMZ host enabled.
10. Corrected: Lose 'G.DMT' item in PPPoE / PPPoA>>DSL Modem Settings.
11. Corrected: DMZ alert problem happened on WUI.
12. Corrected: WAN IP Alias cannot be cleared on WUI.
13. Corrected: 'Schedule' relatively contents is hidden in user mode.
14. Corrected: Display error for WCF LED.
15. Corrected: WLAN Advanced Setting\WMM Configuration is hidden in user mode.
16. Corrected: Auto-detect function submit error "404 Not Found" in Quick Start Wizard.
17. Corrected: Can't clear old configuration when upgrade *.RST firmware by WUI Firmware
Upgrade page.
18. Corrected: SSID can't include " " character.
19. Corrected: Login problem with IE8
20. Corrected: IKE phase 1 proposals are incomplete.
21. Corrected: PPTP WAN connection cannot dial out because of sending GRE encapsulated
TCP packet to server.
22. Corrected: When PPTP WAN connection established, the router can not access LAN that
it belong to.
23. Corrected: Wireless clients can access Web UI in isolated LAN mode when they use 2nd
subnet IP or changed HTTP, HTTPs, SSH, TELNET, FTP port.
24. Corrected: DTMF tone has a loud voice when automatically redials to PSTN line.
25. Corrected: Display problem for the ring port configured in VoIP>>SIP Account.
26. Corrected: Only one phone can loop through to PSTN at the same time for FXS software
relay and hardware relay.
27. Corrected: Allows ring patterns to be selected
28. Corrected: Can't register multiple SIP accounts on VoIP page for some ISP.
29. Corrected: Display error for VoIP LEDs (Phone 1 and Phone 2) in some situations.

[End of File]