****************************************************************************** Release Notes for Vigor2830 series (Dual band for wireless models) Firmware Version : 3.6.4 db Release Date : 7th May 2013 Build Date : 19th March 2013 Applicable Models : Vigor2830, Vigor2830n-plus (Dual band) Vigor2830Vn-plus (Dual band) ADSL Modem Code : 232201 (Standard) Locale : UK Only / Annex A Only ****************************************************************************** NOTE: ADSL Modem Codes For general purpose usage on UK lines, modem code 232201 is recommended For ADSL2+ Annex M lines, the latest modem code 2471201 is suggested For line speeds of less than 4Mbps, on lower quality lines a modem code with more conservative paramaters, 211801 is suggested IMPORTANT NOTE : If your Vigor 2830 unit is a wireless model then this firmware is only suitable for DUAL-BAND models. All 'plus' units are Dual-Band. Most non-Plus units sold from approximately August 2011 onward are single band. Non-Plus units sold before August 2011 may be single or dual-band. If you're note sure which you have, check this guide http://www.draytek.co.uk/support/kb/kb_vigor_2830_dual_band.html [New Features] 1. SSL VPN support up to 5 dial-in users 2. OpenVPN.support for dial-in users 3. Added Web Portal (displays message on connection) in [LAN] – [Web Portal Setup] 4. Added Wireless Configuration Wizard. 5. IPv6 USB LPR printing service. 6. Mail Alert now supports sending mail via SSL / TLS and can specify the SMTP port 7. Web content feature DNS mechanism during activation/authentication improved 8. Web interface can be authenticated through LDAP or user accounts configured from [System Maintenance] – [Admin Setting] 9. Admin Login through WAN can now be disabled 10. DHCP options (ASCII/Hex) can be set under [LAN] – [General Setup] 11. Added a VLAN failsafe option to the [LAN] – [VLAN] section 12. Added an “Always On” checkbox for IPv6 – AICCU tunnel 13. Add VoIP Inter-digit timeout for TR-104. 14. Added a telnet command to set which ADSL modulation types are used with the Modulation set to Multimode: % adsl automode [add|remove|set|default|show][adsl_mode] 15. Support WLAN IGMP snooping. [Improvement] 1. routers handling of AICCU neighbour packets. 2. Time and Date: Daylight Saving doesn't work with time zone Adelaide (GMT +9:30). 3. An issue with sending pings between VLAN subnets 4. 4G WiMAX / LTE web user interface settings could not be saved. 5. VPN: Windows 7 L2TP over IPsec client could not pass traffic immediately after connecting 6. Improved processing of multiple simultaneous PPTP dial in/out connections 7. VPN: If MPPE was enabled, the PPTP Dial-in user VPNs could not connect 8. VPN: IPSec LAN to LAN VPN tunnel could not pass PPTP VPN traffic 9. VPN: PPTP Dial-in user VPNs could not create a PPTP VPN through that tunnel 10. WLAN: Incorrect country code sent which affected Mac and Linux computers connecting wirelessly on channels 12 and 13 11. WLAN: Router was broadcasting SSID when wireless was disabled by schedule 12. The RADIUS request of WLAN clients was rejected by Synology NAS RADIUS server 13. Two IP phones behind NAT are unable to call each other after a period of time 14. SIP ALG: "via" information was not being modified correctly 15. App Enforcement: Now supports blocking RaidCall (v7.0), PPStream (v2.7.0.1512), and Teamviewer (v8.0.16284, v7.0.15723). 16. Load Balance Policy: can now specify a VPN tunnel to pass traffic through 17. Supports connecting to an LDAP Server via hostname. 18. SMS Alert: Added support for "messagebird.com" SMS Service. 19. H.323_alg passthrough support 20. [NAT] – [Open Ports]: can now specify All as a WAN option 21. Time and Date: Modified the NTP DNS resolution period from once every 20 seconds to 10 seconds prior to the time specified by Automatic Update Interval. 22. Corrected routing for WLAN SSID broadcast packets 23. SNMP: IP Routed subnet IP of router would not respond on SNMP 24. The router accepts asterisk (*) as the administrator password. 25. [LAN] – [LAN Port Mirror]: Restart no longer required after changing settings 26. Improved: Web Content Filtering: When the user accesses a website present in two categories with Commtouch, the router can only show/handle one category. [Known Issue] 1. The SSL VPN function uses port 443. If NAT redirecting port 443 to an internal server please change the routers SSL VPN port via [SSL VPN]>[General Setup] Please see http://www.draytek.co.uk/support/kb/kb_sslvpn_troubleshooting.html" 2. MoTP Dial-In User profiles can not be saved via Web UI. A work around is to setup PPTP without MoTP and then use telnet to enable. > vpn dinset ? % vpn dinset % vpn dinset % vpn dinset % vpn dinset motp % vpn dinset pin_secret > vpn dinset 1 Dial-in profile index 1 Profile Name: motep Status: Active Mobile OTP: Disabled Password: 1234 Idle Timeout: 300 sec > vpn dinset 1 motp on % Enable Mobile OTP mode! > vpn dinset 1 pin_secret 1234 123456789abd1234 ****************************************************************************** Release Notes for Vigor2830 series (Dual band for wireless models) Firmware Version : 3.6.3 db Release Date : 31st Dec 2012 Build Date : 15th Oct 2012 Applicable Models : Vigor2830, Vigor2830n-plus (Dual band) Vigor2830Vn-plus (Dual band) ADSL Modem Code : 232201 (Standard) Locale : UK Only / Annex A Only ****************************************************************************** NOTE: ADSL Modem Codes For general purpose usage on UK lines, modem code 232201 is recommended For ADSL2+ Annex M lines, the latest modem code 2471201 is suggested For line speeds of less than 4Mbps, on lower quality lines a modem code with more conservative paramaters, 211801 is suggested IMPORTANT NOTE : If your Vigor 2830 unit is a wireless model then this firmware is only suitable for DUAL-BAND models. All 'plus' units are Dual-Band. Most non-Plus units sold from approximately August 2011 onward are single band. Non-Plus units sold before August 2011 may be single or dual-band. If you're note sure which you have, check this guide http://www.draytek.co.uk/support/kb/kb_vigor_2830_dual_band.html [New Features] 1. IPv6 Support added 2. Support for Smart Bandwidth Limit added 3. SNMP v3 support added 4. Support for QoS DiffServ retagging added 5. Support ADSL PVC to PVC binding. 6. Add VoIP Wizard. 7. Each LAN Subnet now supports setting an individual DNS setting 8. New SMS & Mail Service Object added 9. New load-balance policy function supports the routing requirements for IP routing subnets 10. User Management now supports Web Authentication using either HTTPS or HTTP [Improvement] 1. Removed ADSL2/2+ Annex M from "multimode" auto-detect mechanism due to interoperability issues that could cause incorrect modulation to be set. For Annex M lines please manually set the modulation to Annex M instead of multimode. 2. Resolves an issue that could prevent correct Static route functionality when multi-subnet is enabled 3. Corrects a Routing table display error in [Diagnostic] > [Routing Table] menu 4. Corrects the LAN interface that is displayed for static ARP 5. Resolves an issue that could prevent two computers within the same VLAN from communicating with each other when connecting via different switches 6. Fixes an issue in IGMP snooping which would prevent two IPTV clients from watching the same channel 7. Corrects an issue that could cause Dynamic DNS to force update even though there was no WAN IP change 8. Corrected: Remove the incorrect log of PPP start (XXX), for we don't know who the incoming client is before authenticated by CHAP/PAP. 9. Addresses an issue that would prevent Android phone from obtaining FTP file list from Vigor 2830 FTP server 10. Corrects an issue where NAT port redirection for a WAN1 Alias IP doesn't work when port redirection setting doesn't specifically list the Alias 11. Addresses an issue with True IP DMZ 12. Resolves configuration issues that could occur in [WAN] > [General Setup]- 13. Wireless country string corrected 14. Addresses an issue that could occur with the wireless AP Discovery feature 15. Improved Wireless 802.1x compatibility with linux Radius Server 16. A user can send a FAX not only using T.38 protocol but also G.711. 17. Resolves an issue which would prevent IP Phones behind the Vigor 2830 from registering after a WAN failover because the router would sent UDP packets with a source port of 0. 18. Fixes an issue with sending DHCP Relay via VPN tunnel 19. Addresses an issue with GRE IPsec tunnels 20. Resolves an issue that would prevent AES192 or AES 256 being used as the IKE proposal if AES without authentication is selected as the IPSec Security method 21. Corrected firewall so that is able to block internal router subnet packets 22. URL Content Filter Syslog improved so that it displays HTTP or HTTPS 23. Resolved an issue that would prevent external client from access internal RDP server via IP routing subnet 24. Fixed an issue that would prevent wireless clients successfully completely 802.1x authentication after router reboot 25. Incoming ICMP packets from WAN side can not ping "IP routing subnet" interface IP 26. Fixed an issue that could case CPE to loss connection when it connects to VigorACS server with STUN server. 27. Removed VoIP option in Multi-PCS setting for non VOIP models. Multi-PVCs setting page. 28. Improvments to WCF service stability 29. Clear button added to SIP account page 30. DHCP Server Lease time field added for each subnet. 31. Syslog improved to show which devices have been allocated IP by router 32. Added support to allow the router to send the TR-069 packet out via LAN interface 33. Support GRE over IPsec with CISCO. (4 bytes GRE header) 34. Modified the default pool size of LAN DHCP server from 50 to 150. 35. Correct error with Secondary DNS displayed in Online Status 36. Added new DDNS provider (UBDdns, Oray, and Peanut Shell). 37. Improve Samba compatibility with Mac OS X. 38. Bandwidth Limit range changed to 0 - 30000 39. Port Redirection can shows WAN Interface for each rule in the main page 40. For Safari based browsers the User Management redirection page method has been improved 41. Application Filter updated to support dropbox version 1.4.11 and skype version 5.10.56.116. 42. ADSL state information update frequency decreased from 5 to 30 seconds 43. "Undefined Protocol" DoS defense function renamed as "Unassigned Numbers" 44. Updated 3G modem support including MF190J, AnyDATA ADU-500A, LG VL600 LTE, and LTE Yota LU150 45. Improve the connection performance for Huawei E398/K5005 and Sierra 320U dongle. 46. QoS disabled by default for non-VoIP models. 47. QoS for VoIP enhanced 48. ALG for SoftPhone Polycom and lift-size improved 49. VPN Profile WUI improved 50. UCF/WCF block web page modified 51. SNMP's sysDescr can show model name and firmware version. 52. TR-069 support added for IP Route subnet parameters, firewall parameters, RADIUS parameters, WAN Connection Detection and SysLog / Mail Alert Setup parameters 53. 3G WAN connection Signal parameter status added to TR-069 Renamed TR-069 parameter "InternetGatewayDevice.X_00507F_Firewall.DoSDefense.BlockUnknownProto" to "InternetGatewayDevice.X_00507F_Firewall.DoSDefense.BlockUnassignedNum" 54. ip arp accept telnet command changed to give separate control over behaviour (pass or block) for both incorrect source mac and incorrect destination mac. 'ip arp accept <0/1/2/3/status>' 54. Added a telnet command to configure IGMP Query packet interval time. 'ip igmp_proxy query [msec]' 55. Added a telnet command to configure flash hook minimum and maximum time for VoIP. 56. Added a telnet command to allow VPN packets to instaed go through by NAT if VPN disconnected 'vpn pass2nat ' ****************************************************************************** Release Notes for Vigor2830 series (Dual band for wireless models) Firmware Version : 3.3.7.1 db Release Date : 14st May 2012 Build Date : 10th May 2012 Applicable Models : Vigor2830, Vigor2830n-plus (Dual band) Vigor2830Vn-plus (Dual band) ADSL Modem Code : 232201 (Standard) Locale : UK Only / Annex A Only ****************************************************************************** [New Features] 1. Support SMS (Short Message Service). When WAN backup mechanism is activated the system administrator can be notified via a SMS message to their mobile. 2. Support Common E-mail / Send Syslog via email. 3. Support External Devices Auto-detection mechanism. 4. Removed ADSL2/2+ Annex M from "multimode" auto-detect mechanism due to interoperability issues that could cause incorrect modulation to be set. For Annex M lines please manually set the modulation to Annex M instead of multimode. 5. Support Address Mapping for NAT configuration. 6. Support hardware MD5/SHA1 encryption. 7. Allow Mail Alert to send emails with VPN notifications. 8. Allow the router to be managed and controlled by SmartMonitor. 9. Support 56K AFM102 USB Modem. 10. Support to set DNS for each LAN subnet. 11. Support IP Routing subnet parameters to TR-069. 12. Support System Maintenance>> Login Customization. [Improvement] 1. Improved: Add a new telnet command "voip sip misc -D" to disable/enable VoIP service. 2. Improved: Add a new telnet command "srv dhcp custom_option" which allows a user to enter user-defined "DHCP option". 3. Improved: Support disable/enable user mode on WUI. The factory default setting is disabled. 4. Improved: Improve the compatibility with VigorACS SI v1.08 5. Improved: SIP address format (either Withheld@.. or anonymous@.. ) can be blocked if Block Anonymous under VoIP>>DialPlan>>Call Barring is configured. 6. Improved: Incoming calls with SIP from header field without having an account name (e.g., tagged with 5E623524-172D) can be blocked if Block Anonymous under VoIP>>DialPlan>>Call Barring is configured. 7. Improved: Corrected some SNMP reporting for LAN status 8. Improved: Support Syslog Explorer with Web Syslog and USB Syslog under USB Application. 9. Corrected: DDNS does not upgrade automatically when the DDNS account is set for WAN2 only. 10. Corrected: Data Flow Monitor does not show TX value for the monitored IP address and RX value for WAN1 on PPTP Host-LAN environment. 11. Corrected: Can not connect VPN via 3G (WAN3) when WAN1 or WAN2 is connected. 12. Corrected: RIP over VPN does not work. 13. Corrected: My WAN IP setting does not work for PPTP in VPN NAT mode. 14. Corrected: Can not create LAN-to-LAN VPN connection via WAN3 when WAN1 or WAN2 is connected. 15. Corrected: My WAN IP setting does not work for PPTP in VPN NAT mode. 16. Corrected: A compatibility issue occurs when IPSec Aggressive mode is used and set with local IP address. 17. Corrected: User-Based mode of user management does not work if HTTPS management port has been changed. 18. Corrected: WAN cannot get IP from DHCP server when Block Fraggle Attack is checked in the page of Firewall>>DoS Defense. 19. Corrected: Ping detection failed when target IP and gateway are in the same subnet. 20. Corrected: When WAN 1 is disconnected, the router can not send the SIP register packets of internal VoIP phones via WAN2 port automatically. 21. Corrected: VigorPhone350 loses registration behind NAT after one or two weeks 22. Corrected: NAT improvments to previous VoIP calls disconnecting after 2-3 minutes 23. Corrected: Wireless client cannot access LAN network from another AP that's connect to 2830 wireless LAN. 24. Corrected: Corrected syslog log display error showing http:// rather than https:// for keyword blocked visits to https sites. 25. Corrected: The minimum value is 48 seconds for the session-timer setting in "VoIP >> Phone Settings " 26. Corrected: Remove "Ultrasurf" from Web Content Filter WUI. ****************************************************************************** Release Notes for Vigor2820 series (Dual band for wireless models) Firmware Version : 3.3.6.1db Release Date : 16th June 2011 Build Date : Jun 1 2011 12:00:11 Applicable Models : Vigor2830 Vigor2830n (Dual band) Vigor2830Vn (Dual band) ADSL Modem Code : 232201 (Standard) Locale : UK Only / Annex A ****************************************************************************** NOTE: ADSL Modem Codes For general purpose usage on UK lines, modem code 232201 is recommened For ADSL2+ Annex M lines, the latest modem code 2471201 is suggested For line speeds of less than 4Mbps, on lower quality lines a modem code with more conservative paramaters, 211801 is suggested [New Features ] - Support for Motive ACS Platform - Additional Notifcation functions in TR-069 - PPP Assignments for LAN2/3/4 start at 200, like LAN1 [ Changes / Improvements] - Corrected : Instability if WLAN MAC address access control was enabled - Corrected : DNS proxy now provided for DHCP clients by default - Corrected: telnet command: wol fromWan on/off - lets WOL packet pass from WAN to LAN. - Corrected: Incorrectly configured 802.1x clients could not connect to WLAN - Corrected: Modify the error correction telnet command for FAX relay. - Corrected: The APP Enforcement may not always work in user management. - Corrected: Release buffer failed when VPN is L2TP over IPSec and WAN setting is PPTP. - Corrected: Protocol error occurred in predefined QoS service (SMTP and NNTP). - Corrected: Modify "Apply to 2nd subnet" to "Apply to IP Routed Subnet" on Bandwidth Management >> Bandwidth Limit page. - Corrected: NTP may not work when using 3G modem connection - Corrected: If HTTPS management port has been changed, the redirection page not shown - Corrected: Session Version in SDP is not incremented in reINVITE. - Corrected: Web configruator login authentication was not available to all LAN subnet IPs. - Corrected: When outbound QoS is enabled, PPPoE packet may be queued and resulted in dial-up failure - Improved: NAT Session Full problem occurred in some case. - Improved: Add error recovery packets in T.38 redundancy mode. - Improved: Modify NTP client backup mechanism. Always retry user defined NTP server when backup server fails (for isolate network). - Improved: Remove IP address with x.x.x.0 and x.x.x.255 in DHCP table IP list and hidden conflict IP for LAN IP. - Improved: Show "Invalid IP Address!" for IP Ping when there is no available interface. - Improved: Remove Multi-PVC page in user mode. - Improved: Rename “Tag-based Bridge” tab from Multi PVC page to "Port-based Bridge" - Improved: On WLAN menu ****************************************************************************** Release Notes for Vigor2830 series Firmware Version : 3.3.6 (First Firmware Release) Release Date : 28th January 2011 Build Date : 15th November 2010 Applicable Models : Vigor2830, Vigor2830n, Vigor2830Vn ADSL Modem Code : 232201 (Standard) Locale : UK Only / Annex A Only ****************************************************************************** First Firmware Release [END OF FILE]