*************************************************************************** Release Notes for Vigor 2920 series Firmware Version : 3.6.3 Release Date : 14th December, 2012 Build Date : 29th November, 2012 Applicable Models : Vigor 2920 series *************************************************************************** [New Features] 1. Add SNMPv3 support 2. Add SMS object and Notification object configuration for SMS application. 3. Support customized profile for DDNS. 4. Support printer client print information to syslog. 5. Support web portal for LAN. [Improvement] 1. Disable QoS setting by default for non-VoIP models. 2. Resolved stability issue caused by the WCF mechanism. 3. IP Route Option in Bandwidth Limit page wouldn't stay disabled after a reboot 4. While using an IP routing subnet, the external client can't access internal routing client via RDP. 5. A VPN profile with static IP assignment can allow more than one users dial in. 6. QoS classify error for transmission traffic to VPN L2TP tunnel. 7. Windows7 takes 30 seconds to register L2TP over IPSec VPN connection when MS-CHAPv2 is in use. 8. Improvements to VPN server for processing more than 10 Remote Dial-In Users 9. DHCP over IPsec improvements 10. DMZ/Open Ports page is not allowed to choose IP address in bind IP list. 11. May not connect to specific IPv6 tunnel broker. 12. Wake on LAN doesn't work well when enabling LAN VLAN tag. 13. Wake on LAN doesn't work after 15 minutes while using WakeOnLanGui.exe on WAN side. 14. Solve the WAN1/WAN2 link speed problem. 15. Corrected an issue with running Wireless AP Discovery 16. Fixed Wireless schedule 17. Wireless clients with 802.1x may not connect to the router after router reboot. 18. Got error message while setting the bandwidth limit. 19. WAN2 QoS syslog display error. 20. Corrected QoS traffic graph or the "Other" class in WAN 2 21. WAN Incoming ICMP packets can not ping "routing subnet" interface IP. 22. TR-069 stun didn't work after changed the stun server port 23. PPPoE dial-up may fail after received CCP Request. 24. DHCP Table shows many additional DHCP entries when changing LAN1 subnet mask. 25. The router will broadcast DHCP request across all VLANs which are isolated from each other. 26. If outbound proxy is enabled, the first destination/stop for all the outgoing SIP messages from our router should be the "outbound proxy" specified. 27. Softphone is connected behind NAT. When we make the outgoing call, the syslog still shows " 0 VoIP calls detected...(NAT:0) ". 28. Add limitation for the maximum length of password in VPN profile. 29. Support DHCP relay for each VLAN (LAN 2 to LAN4). 30. Add flash hook minimum and maximum time for VoIP model. 31. Add the feature of Enable ping to keep alive for VPN connection for TR-069. 32. Add TR-09 parameter support for "setting WAN Connection Detection", "WAN interface VLAN ID parameters", and "VPN lan to lan status parameters" 33. Support TR-069 packets out via LAN interface. 34. Support that each subnet has a configurable DHCP server lease time. 35. Support that a DHCP syslog can be issued whenever an IP has been given out returned back from the pool. 36. Support GRE over IPsec with Cisco (4 bytes GRE header). 37. Support to block ultrasurf. 38. Support the Oray DDNS. 39. Improved wireless WPA2/802.1x mode with Linux Radius Server. 40. Alert Mail for Test and WAN disconnection doesn't bring the set Router Name. 41. Corrected issue where Yahoo Email is blocked by APPE>>MISC>>Wujie/UltraSurf. 42. Brazil SIP RFC3261 conformance Test. 43. Changed the word from "Edit" to "Update" on Bandwidth Limit page. 44. Change Moscow GMT Time zone from GMT+3 to GMT+4. 45. Support Wake on LAN for UDP Port Redirection for any (0.0.0.0) host by telnet command. "wol fromWan " ?? Improved: Support to disable the WINS server in DHCP configuration by telnet command. "srv dhcp primWINS clear" "srv dhcp secWINS clear" 46. Configure IGMP Query packet interval by telnet command. "ip igmpproxy query " *************************************************************************** Release Notes for Vigor 2920 series Firmware Version : 3.6.0 Release Date : 11th July, 2012 Build Date : 8th July, 2012 Applicable Models : Vigor 2920 series *************************************************************************** [New Features] 1. Support added for IPv6. 2. Support added for Smart Bandwidth Limit. 3. Support DNS setting for each LAN subnet. 4. Support LAN wired 802.1x. 5. Support QoS retag. [Improvements] 1. Corrected: Issues setting static route doesn't work when multi-subnet is enabled. 2. Corrected: LAN1 will be displayed always while setting any static route for LAN2/3/4. 3. Corrected: Routing table display error in Diagnostic>>Routing Table page. 4. Corrected: Wrong LAN interface for static ARP is displayed. 5. Corrected: Both computers with the same VLAN cannot communicate for each other when connecting to different switch. 6. Corrected: IGMP snooping problem. 7. Corrected: Can not open the Switch P2260 web configurator via External Device. 8. Corrected: The wireless client can't access internal network from another AP and return to Vigor2920 wireless LAN. 9. Corrected: DNS function does a force update even though no WAN IP changed. 10. Corrected: DHCP Relay via VPN tunnel can not work. 11. Corrected: Remove incorrect log entry of PPP start (XXX), before it is authenticated by CHAP/PAP. 12. Corrected: IP Phones behind Vigor2920 cannot get registration after WAN Failover (Router sent UDP packets with source port 0). 13. Corrected: Cannot apply AES 192 and AES 256 on IPSec Security Method while the customer chooses options of AES without Authentication in VPN and Remote Access >> LAN to LAN page. 14. Corrected: Firewall can't block internal routing subnet packets. 15. Corrected: UCF Syslog cannot show HTTP or HTTPS. 16. Corrected: Can not show the FTP file list when Android phone connecting to Vigor2920 FTP server. 17. Corrected: ISDN Internet connection cannot work with miniVigor128. 18. Improved: Remove Ultrasurf from WUI. 19. Improved: Modify UCF/WCF block web page. 20. Improved: Support IP Route subnet parameters setting for TR-069. 21. Improved: Support firewall parameters setting for TR-069. 22. Improved: Support RADIUS parameters setting for TR-069. 23. Improved: Support Maintenance >> SysLog / Mail Alert Setup parameters setting for TR-069. 24. Improved: Modify the default pool size of LAN DHCP server from 50 to 150. 25. Improved: Online Status shows error Secondary DNS value. 26. Improved: Improve VPN Profile WUI. 27. Improved: Improve Samba with MacOS X. 28. Improved: Modify the Telnet command of "ip arp accept <0/1/2/3/status>" to allow the ARP REPLY which Target's MAC address does not equal to Ethernet source MAC address. 29. Improved: Enhance VoIP QoS. 30. Improved: Add new DDNS provider (UBDdns, Oray, and Peanut Shell). 31. Improved: Support modems such as ZTE K3806, and MF192, and MF190J, QT-R220, LG VL600 LTE, LTE Yota LU150. 32. Improved: Add a telnet command for VPN packets going through by NAT or not when VPN disconnects. vpn pass2nat *************************************************************************** Release Notes for Vigor 2920 series Firmware Version : 3.3.7.1 Release Date : 18th April, 2012 Build Date : 8th November, 2011 Applicable Models : Vigor 2920 series *************************************************************************** [New Features] None [Improvements] 1. Correct issue with PPPoE connection via some ISPs 2. Fixed: Configuration backup might cause system crash for TR-069. 3. Improved: Add parameters for wireless connection for TR-069. 4. Support IPSEC X.509 with Cisco Router for VPN. 5. Support VoIP call via VPN. 6. Support Huawei E173, Nokia CS11/CS12, Alcatel X200L, ZTE MF110/MF190/K3571-Z for 3G connection. 7. Support accessing into WUI by using Safari browser for web authentication. 8. Support DDNS service through freedns.afraid.org. 9. Support add/delete object for TR-069. *************************************************************************** Release Notes for Vigor 2920 series Firmware Version : 3.3.7 Release Date : 25th November, 2011 Build Date : 3rd October, 2011 Applicable Models : Vigor 2920 series *************************************************************************** [New Features] 1. Support up to 30-nodes with DrayTek SmartMonitor 2. Support VPN Backup for VPN TRUNK Management. 3. Support multiple subnets for LAN configuration. 4. Support BPjM for Web Content Filter in Service Activation Wizard. 5. Support Auto-detection mechanism to display other DrayTek devices (routers, switch, AP) on the same subnet. See [External Devices] setting in Web UI. 6. Support Address Mapping for NAT configuration. 7. Support hardware MD5/SHA1 encryption. 8. Allow Mail Alert to send emails with VPN notifications. [Improvement] 1. Corrected: Cannot input 64 character IPSEC Pre-Shared key via Telnet. 2. Corrected: RADIUS authentication doesn’t work via VPN tunnel. 3. Corrected: DNS query always fails if DNS server is not in WAN side. 4. Corrected: Unencrypted PPTP connection can be established even if "Require MPPE" or "Maximum MPPE" is selected. 5. Improved: telnet login attempts recorded to Syslog 6. Corrected: DDNS does not upgrade automatically when the DDNS account is set for WAN2 only. 7. Corrected: XBOX 360 can not be connected to Vigor2920 with WPA2. 8. Corrected: Between Vigor2920n and Vigor AP700, only WEP can be used in Wireless LAN >>WDS for the network security. 9. Corrected: NAT session maintenance/housekeeping improvments 10. Corrected: RIP over VPN does not work. 11. Corrected: DoS defense still active even if set to disabled. 12. Corrected: Can not connect VPN via 3G (WAN3) when WAN1 or WAN2 is connected. 13. Corrected: Data Flow Monitor does not show TX value for monitored IP address and RX value for WAN1 on PPTP Host-LAN environment. 13. Corrected: My WAN IP setting does not work for PPTP in VPN NAT mode. 14. Corrected: Can not create LAN-to-LAN VPN connection via WAN3 when WAN1 or WAN2 is connected. 15. Corrected: Buffer leak occurs when IPSec Aggressive mode is used and set with local IP address. 16. Corrected: User-Based mode of user management does not work if HTTPS management port has been changed. 17. Corrected: WAN cannot get IP from DHCP server when Block Fraggle Attack is checked in the page of Firewall>>DoS Defense. 18. Corrected: Ping detection failed when target IP and gateway are in the same subnet. 19. Corrected: When WAN 1 is disconnected, the router can not send the SIP register packets of internal VoIP phones via WAN2 port automatically. 20. Corrected: General NAT mechanism improvments including fixes for NAT session issues seen with IP phones. 21. Improved: SIP address format (either Withheld@X or anonymous@X ) can be blocked if Block Anonymous under VoIP>>DialPlan>>Call Barring is configured. 22. Improved: Incoming calls with SIP from header field without having an account name (e.g., tagged with 5E623524-172D) can be blocked if Block Anonymous under VoIP>>DialPlan>>Call Barring is configured. 23. Improved: Correct some SNMP information for LAN status. 24. Improved: Total TX/RX information can be shown in Diagnostics>>Traffic Graph. 25. Improved: Improve the compatibility with VigorACS SI. 26. Improved: Support Syslog Explorer with Web Syslog and USB Syslog under USB Application. 27. Improved: Support Comment feature in LAN>>Bind IP to MAC. 28. Improved: The limit settings for Bandwidth Limit can be modified in Kbps or Mbps. 29. Improved: Support disable/enable user mode on WUI. The default setting is disabled. 30. Improved: Add a new telnet command "voip sip misc -D" to disable/enable VoIP service. 31. Improved: Add a new telnet command "srv dhcp custom_option" that allows a user to enter custom-made "DHCP option". *************************************************************************** Release Notes for Vigor 2920 series Firmware Version : 3.3.6 Release Date : 6th December, 2010 Build Date : 17th November, 2010 Applicable Models : Vigor 2920 series *************************************************************************** [New features] 1. Add Support Area with Product Registration function on WUI. 2. Add shared mode to bandwidth limitation. 3. Add signatures to block APP including MSN web games and APP actions, voip application: TeamSpeak 3.0, ICQ web access, ICQ Zones, YahooIM SSL Login and YahooIM Invite Voice, YahooIM Register SIP, YahooIM Invite SIP. 4. Add SMTP port configure for mail alert function. 5. Support loging Web UI system reboot information to Syslog. 6. Support static IP mode on VPN remote dial-in. 7. Support Corbina PPTP/L2TP server. 8. Support GlobalView Web Content Filter (WCF) service 9. Support mOTP. 10. Support User Management. 11. Support USB File System. 12. Support ISDN USB (MiniVigor 128). 13. Support WLAN SSID VLAN. 14. 3G HSO driver supports ping detection. 15. Support 3G modem including Alcatel X200X and Mobidata MBD-220HU (china), DLink DWM 156 new firmware, ZTE MF628 and Vodafone K3565-Z. 16. Support Multi-VLAN tagging for Ethernet WAN(1). 17. 3G WAN interface can be used independently or be the backup WAN interface for WAN1/WAN2. 18. Support jumbo frame feature on Giga switch (telnet command only). [Improvement] 1. Improved: Got problem while using IE8 browser, Chrome browse and Safari browser on System Status of WUI. 2. Improved: Upgrade VoIP TAPI driver to v3.7.1. 3. Improved: Allow the IP address and domain name in VPN setup command. 4. Improved: Add more WLAN/VLAN parameters for TR069. 5. Improved: Can not accept the invite packet of VoIP while packet size is more than 2048 bytes. 6. Improved: Add a telnet command wan ppp_mru to fix the PPP IOP issue in Netherlands VDSL networks. 7. Improved: Modify the Interval Time of Periodic Inform Settings on System Maintenance>> TR-069 from 900 to 3600 seconds to reduce the ACS server loading. 8. Improved: WAN cannot get IP from DHCP server when Block Fraggle Attack on Firewall>>DoS Defense is enabled. 9. Improved: Remove Winny from CSM list bBecause behavior detection method to block winny sessions can cause false-positive matches and block some normal sessions. 10. Improved: Remove syslog message if wireless security mode is 802.1x with WEP. 11. Improved: Use Router's Model name as UPnP friendly name. 12. Improved: Support IPSec AES in Phase I for Aggressive mode. 13. Improved: Remove the restriction of Open Ports that local IP and LAN IP must be in the same subnet. 14. Improved: Send TR069 BOOTSTRAP packet to ACS server while the router is reset to default. 15. Corrected: HSO driver won't disconnect broadband connection while removing the device. 16. Corrected: SSH remote management doesn't work when DMZ is open to a host. 17. Corrected: Router instability while executing WLAN restart. 18. Corrected: Router instability while running Foxy/eMule services. 19. Corrected: Router instability while WLAN is on auto channel selection mode. 20. Corrected: The connection is "broken" for 30-60 sec every 30-min because of incorrect T1/T2 lease time of DHCP client. 21. Corrected: VPN LAN to LAN profile error after retrieving the factory default setting from WUI. 22. Corrected: Handling DNS request for SRV type and no answer issue 23. Corrected: Router accepts PPTP/L2TP sever assigned IP address in IPCP negotiation, but it can be overwritten with fixed address if set in IPCP opening. *************************************************************************** Release Notes for Vigor 2920 series Firmware Version : 3.3.2.3 Release Date : March 04, 2010 Applicable Models : Vigor 2930 series *************************************************************************** First Firmware Release. [END OF FILE]