************************************************************************************ Release Notes for VigorIPPBX 2820 Firmware Version : 3.5.5 (Release Version) Release Date : 25th Aug 2010 Build Date : 25th Aug 2010 Applicable Models : VigorIPPBX 2820 ADSL Modem Code : 232201 (Standard) Locale : UK Only ************************************************************************************ [New Features] For IPPBX functionality 1. Support call pickup function. For specific extension pickup or group pickup. 2. Support Call barring with wildcard match; the rule set can apply to all, extension or group. 3. Support Call forward to external number via SIP Trunk. 4. Support hunt group overflow handling. 5. Support choice of CLI for outgoing call. 6. Support FXO function. (Digitmap does not currently support FXO as an outbound route. FXO trunk number should be dialled directly) 7. Support Digitmap backup route function. 8. Support Digitmap wildcard match function. (can use this feature to setup default sip trunk) 9. Support CDR export function. 10. Support extension/sip trunk setting backup function. 11. Support simultaneous 4-ISDN calls from two ISDN-TE ports. 12. Add telnet command to assign SIP Trunk CODEC priority, please see note for the usage. For Firewall/Router functionality 1. Support USB Disk related applications. 2. Support IPSEC AES mode 3. Support mOTP for VPN remote dial-in user. 4. Support NAT address mapping function. 5. Support NAT Port Trigger function. [Improvement & Corrections] 1. Support off-net call transfer. 2. Enhance BLF performance. 3. Support smtp port setting for voice mail function. 4. Fixed access rule not work for USB based samba application. 5. Allow extension client to press "Missed" menu button to call an external number back. 6. Add activate action when detect ISDN line exist or not. 7. Fixed extension setting change will cause status display error when number not same with display name. 8. Enhance ISDN-TE channel voice quality. 9. Correct IVR behavior when set to "not used" option. 10. Fixed ISDN-TE offnet no dial tone and cause dsp crash issue. 11. Fixed an issue where IPPBX incorrectly identified the VoIP-unlimited call hold re-invite packet as new invite request. 12. Extended the IVR length from 24 sec to 75 sec. 13. Correct some IPPBX telnet commands not work well issue. 14. Add two telnet command to adjust busy detection and echo canceler. 15. Add a telnet command that can tune the level and the twist of the DTMF detection. 16. Add telnet command to disable/enable support of remote extensions, see note. 17. Fix codec save error in WEB VoIP >> SIP Accounts 18. Add No registration call option into sip trunk WUI setting. 19. Fixed web issue for call barring setting. 20. Remove miss-added Multi-VLAN WUI page. 21. Add UK_CCA, Taiwan and China option in Advance Settings Tone Setting Region. 22. Fixed situations where RTP stream would contine after call had terminated. 23. Support backup config data mechanism to prevent setting became factory default after reboot. 24. An extension without build session can not dial to park server directly. 25. Fixed incoming call to hunt group number, can not do call park issue. 26. Fixed group call rtp proxy issue. 27. Fixed PBX crash issue when receiving SIP 183 message. [Known Issues] 1. IPPBX doesn't relay BYE packet from an off-net caller to an off-net callee for calls via SIP trunk. 2. Hunt group overflow rule is ignored if no members of hunt group are "online". 404 not found response is returned instead 3. Use VigorPhone firmware 12202.26.1.05 or later. Audio distortion can occur with earlier VigorPhone firmware due to RTP CODEC negotation issue in earlier VigorPhone firmware. 4. When 4-ISDN calls are used simultaneously it might mean that PSTN trunk does not have a DSP channel available for its use. This would mean that DTMF keypresses would not be recognised by the IVR. 5. Use version later than V2154 for VigorTalk ATA24, otherwise a continuous call transfer issue could occur and cause IPPBX reboot. [Notes] 1. For new telnet command, you can use the following command to setup CODEC priority > ippbx lineSetting sip 1 -C 8,0,18 // this will set into SIP Trunk 1, with CODEC 711A > 711U > 729 2. To disable/enable support of remote registration > ippbx pbxSystem remRegEnable [enable|disable|?] enable: permit remote registrations disable: disable remote registrations, IPPBX will not respond to WAN packets sent to SIP Local port ?: Show current status ************************************************************************************ Release Notes for VigorIPPBX 2820 Firmware Version : 3.5.4 Release Date : 17th Feb 2010 Build Date : 25th Jan 2010 Applicable Models : VigorIPPBX 2820 Locale : UK Only ************************************************************************************ [New Features] 1. Support ISDN MSN mapping to extensions 2. Support SIP trunk line register via VPN. 3. SMTP port for voice e-mail can be changeable. [Improvements and Corrections] 1. Callers do not need to press # to select an Auto-Attendant menu option 2. Call Barring method using URI/URL improved 3. Auto-provisioning now allows Extension Number and Display Name to be different 4. IVR Prompt upload now supported via Web Interface 5. Incoming Voicemail from external callers improved 6. Improvements to Auto-Attentant to correct situations where call wasn't being passed to extension / hunt group 7. Improvements to Call Transfer interoperability with various IP phones 8. Added Attended Call Transfer support 9. Interoperability improvements for outgoing calls via SIP Trunk 10.Resolves an issue where ISDN Port 1 was unable to make / receive calls when set to TE mode. 11.Resolves an issue where outgoing call to PSTN via SIP Trunk could cause router reboot. 12.The router will intercept phone call that don't belong to the (MSN) number set in the router. 13.Resolved incorrect model name reported to Vigor ACS system. 14.Quick start wizard displays the wrong interface name. 15.Data flow monitor display issue resolved 16.Improved WUI error checking function. 17.Improved robustness of NAT stress test. 18.Improved interoperability with VigorPhone350. [Known Issues] 1. The web based upgrade will incorrectly accept Vigor2820 firmware but this will render the router inoperable until correct firmware has been loaded. Only use VigorIPPBX 2820 firmware with VigorIPPBX 2820. 2. Interoperability issue with Call Transfer from Cisco 7940 IP Phone 3. For DTMF relay, a user must use outband mode (RFC-2833) in IP phone, FXS and ISDN phone. 4. This version doesn't support call routing. 5. Problem of NMAP scan. 6. The VoIP T.38 fax relay function is not supported yet. 7. The router is unstable when the user uses P2P software, e.g., Foxy. ************************************************************************************ Release Notes for VigorIPPBX 2820 Firmware Version : 3.5.3 (First Firmware Release) Release Date : October 29th 2009 Build Date : September 21th 2009 Applicable Models : VigorIPPBX 2820 Locale : UK Only ************************************************************************************ [END OF FILE]