****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.3.5.1 (Release) Release Date : 4th October 2010 Build Date : 4th August 2010 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [Improvement] 1. Corrected: Globalview WCF Activation wizard was missing in the web interface. 2. Corrected: SSH remote management doesn't work when DMZ host is configured. 3. Corrected: The router will not accept invite packets if the packet size is more than 2124 bytes. 4. Corrected: An incoming fax with T.38 could cause router instability. ****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.3.5 (Release) Release Date : 8th September 2010 Build Date : 4th August 2010 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [New Features] 1. Support T.38 function 2. Support Globalview WCF 3. Support USB disk file explore on WUI 4. Support MX Type DNS Query 5. Support FSK caller ID detection 6. Support DTMF caller-ID format [Improvement] 1. Corrected: Setting problem on Codecs in VoIP >> Phone Settings page. 2. Corrected: Resolved issue where a reboot could occur under some circumstances with VoIP calls. 3. Corrected: Resolved issue where a reboot could occur when doing a call transfer. 4. Corrected: WLAN LED will be on while the WLAN function is disabled using a schedule. 5. Corrected: Resolved issue with PPTP passthrough not functioning correctly. 6. Corrected: Resolved issue saving Interval Time of Periodic Inform Settings in System Maintenance>>TR-069. 7. Corrected: Crash occurs when TR-069 session times out. 8. Corrected: HTTPS URL (without port) setting in ACS Server URL for TR-069 function doesn't work. 9. Corrected: Web interface error while setting service name or comment with '\' in NAT >> Port Redirection or NAT >>Open Ports page. 10. Corrected: Resolved disconnection / reboot issue when enabling ping detect with 3G backup. 11. Corrected: Resolved the issue that a certificate may not be sent out while sending Cert Request in inR2_outR3 or some remote sites like Cisco PIX. 12. Corrected: Fixed a problem with an established PPTP tunnel receiving a protocol rejected message from the peer. 13. Corrected: IP trace route and IP ping use the wrong source IP addresses when using PPTP/L2TP WAN when the destination IP is set as a static route. 14. Corrected: Resolved issue with True DMZ in which the router's NAT would block GRE requests, which would stop PPTP VPN connections establishing. 15. Improved: Modified "Static or Dynamic IP (DHCP client)" to "Static or Dynamic IP" on MPoA page. 16. Improved: Support for HuaWei E1762/E1550 3G modems. 17. Improved: The login page now shows an error message if the username / password are incorrect. 18. Improved: An issue with multiple Draytek DHCP servers using the same transaction ID has been resolved. 19. Improved: Modified the telnet command (arp cache table) for deleting the ARP entry, from 180 seconds to 40 seconds once ARP cache entry expires. 20. Improved: Reword the "ip arp setCacheLife" command. 21. Improved: The web interface page for Hardware Acceleration has been removed due to auto detection by Vigor router. ****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.3.2.3 (Release) Release Date : 8th September 2010 Build Date : 4th March 2010 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [New Features] 1. Support Vigor ACS SI [Improvement] 1. Corrected: Resolved issue with VoIP. When both phones have a call in progress, if Phone 2 hangs up to pick up an incoming PSTN call, the router will reboot. 2. Corrected: The router reboots while carrying out two consecutive Call Transfers. 3. Improved: display error message for username or password in login page. ****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.3.2 (Release) Release Date : 4th Feb 2010 Build Date : 27th Nov 2009 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [New Features] 1. Support USB Disk Application (FTP/Samba). 2. “twodns” DDNS service. 3. Show source MAC address on Syslog for LAN to WAN packets. 4. Added support for Sierra 597 USB 3G Modem. 5. Add Specify Gateway IP Address in Internet Access >> PPTP web page. 6. Add L2TP in Internet Access >> PPTP web page. 7. Support domain name in PPTP server address page. [Improvement] 1. Corrected: Dial Out Account can not be set to default on DialPlan Setup of WUI. 2. Corrected: If the phone is disabled but the phone state is not changed, the phone will not ring when receiving PSTN incoming call. 3. Corrected: Resolved issue that When RFC-2833 with payload type = 96 packet is received, the router will reboot. 4. Corrected: SIP memory leakage. 5. Corrected: Problem for semi-attendent CT for VoIP. 6. Corrected: Some problems occurred on WUI. 7. Corrected: Can not get TR069 parameters after meeting TR069 connection timeout. 8. Corrected: Firmware upgrade may be failed when upgraded by TR069. 9. Corrected: UCF can save 12 objects, only. 10. Corrected: Call filter malfunctioning. 11. Corrected: Failure of running IP Ping through PPTP of VPN. 12. Corrected: Adding UPNP port mapping failed. 13. Corrected: Connection problem on PPTP NAT pass-through. 14. Corrected: Got connection problem while adding session(s) to Hardware PPA table if the packet comes from WLAN. 15. Corrected: Incorporate hardware acceleration into data flow monitor. 16. Corrected: Problem in PPTP WAN DHCP mode. 17. Improved: Wildcard '?' can be used in Digit Map. 18. Improved: Allowed VoIP number starting with # for non-IP calls. 19. Improved: Wireless interoperability with Vigor AP700 while using WDS with WPA or WPA2 mode. 20. Improved: Mouse cursor stays on the field of Username in Login page of Web UI. 21. Improved: Add/modify some TR069 parameters. 22. Improved: Router stability against NMAP scan. 23. Improved: Bridge mode may not work after powering off/on. 24. Improved: Add/modify some IM/P2P signatures. 25. Improved: ARP cache life settings stored to flash so that value is saved even after reboot of the router. 26. Improved: Increase compatibility with more stun servers. ****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.3.1.2 (Release) Release Date : 24th November 2009 Build Date : 29th October2009 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [Improvements & Corrected Problems] 1. Improved: 3G uploaded performance improved for certain conditions 2. Corrected: Resolved issue where Call Transfer to local phone could trigger reboot. Busy tone now played when call transfer to local phone attemped. 3. Corrected: Redialing a phone to PSTN via "digit map" and "phone book" will cause loop tone and can't be stopped when PSTN is in use. 4. Corrected: Flashing LED if SIP phones are in use and PSTN is incoming. 5. Corrected: Problem of Model Name shown in WUI and TR069. 6. Corrected: Close TR069 port if the router is disabled. 7. Corrected: Inform with default WAN connection ExternalIPAddress for Tr069. 8. Corrected: Can't hear anything when a phone is dialed to an iptel account with SIP number. 9. Corrected: VPN services enabled by default. To enabled VPN pass through, disable VPN services via telnet > vpn remote PPTP off > vpn remote ISPec off (NOTE: case sensitive command!) 10. Corrected: Got undefined error in Ping Diagnosis WUI. 11. Corrected: Got a warning message in Diagnostics >> Traffic Graph WUI 12. Corrected: Cannot reset session of date flow monitor while using "portmaptime –f" command. ****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.3.1 (Release) Release Date : 10th August 2009 Build Date : 29th July 2009 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [New Functions] 1. Support 3G backup function. Please send any reports of new USB modems that you have used with the Vigor2110 to http://www.draytek.co.uk/support/techquery.html [Improvements & Corrected Problems] 1. Improved: Added protection mechanism for blocking loop-through while making PSTN on-net/off-net. 2. Improved: enable echo canceller to improve line echo. 3. Corrected: FTP connection session is not added into PPA table. 4. Corrected: VoIP CODEC negotiation capability. 5. Corrected: PPLive can't be blocked. 6. Corrected: Wrong word display for telnet command of "sys autoreboot". 7. Corrected: While doing the second loopthrough on phone2, the router cannot loop through to PSTN line normally. 8. Corrected: A system crash will occur when ringing from PSTN line and network side at the same time. 9. Corrected: LED does not flash when an incoming call arrives via PSTN. ****************************************************************************** Release Notes for Vigor2110 series Firmware Version : 3.2.1 (First Firmware Release) Release Date : 2nd May 2009 Build Date : 22nd September 2008 Applicable Models : Vigor2110n, Vigor2110Vn Locale : UK Only ****************************************************************************** [End of File]